In an embedded device, during the initializing of memory locations, is there any convention that are being practiced.
I mean, say setting every byte to zero or 0xFF or any other value.
Modern embedded devices often have (at least) 3 kinds of memory. If you are in charge of the startup code, you might consider doing something like this:
At boot time (on power-up, and also whenever the watchdog times out), typical startup code ("
This doesn't mean that an uninitialized value (heap or stack) will be zero. If you assume that it is zero, it may seem to work the first time, but after the program runs for a while and re-uses heap and stack a few times, it probably will no longer be zero, leading to intermittent and difficult-to-debug errors.
As Autocracy pointed out, many debugging tools set un-initialized RAM to some other magic value, to more quickly detect this "incorrectly assumed it was zero" bug and other bugs.
A few bit-flip soft-error-tolerant programs re-initialize RAM from ROM as often as possible -- there is no "initialization" code, all the initialization stuff happens inside the main loop. The stack pointer is re-initialized to the beginning of stack RAM at the beginning of each and every pass through the main loop, the baud rate registers are re-set to give 9600 bps each pass through the main loop, the complete time and day is read from the RTCC once a second even when you're pretty sure it's still Wednesday, etc.
Flash data memory: A program that writes new data into a block of flash memory must first erase the entire block. Erasing a block typically takes orders of magnitude more time than reading a block of data from flash. Immediately after erasing, the value of such "blank" memory locations is -- for no good reason that I am aware of -- the all-ones pattern 0xFF. The common convention is to leave unused blocks as that 0xFF pattern, and to immediately "pre-erase" data blocks as soon as they are are no longer needed to that 0xFF pattern, so that later when we need to store data into that block, we can immediately write the data (or at least we only need to wait the remaining time-to-erase).
Program memory (often in ROM or flash memory):
At boot time, the CPU will start executing the startup code ("
What to do with unused memory can also depend on the intended use. For safety critical software, it is common to fill unused memory with commands that force the system into a safe state. As a rudimentary example, software that controls an oven might have all of its unused memory locations filled with jump commands that jump to a safe state function which would ensure that the oven is turned off. This way, if the program counter is inadvertently corrupted (darn those pesky sunspots!), you could at least increase your chances of handling it safely.
The answer is: It Depends.
If you program in C, the language definition states that only static variables that are not initialized will be set to 0 at program start time. If you look at the typical run-time system provided by embedded compiler makers, most include either some or all source code, and you can see there explicit zeroing of the section used for non-const variables.
Variables declared const are usually placed in a separate memory section, frequently ROM or flash EPROM. And initialized variables have the initial values gathered into a block of ROM or Flash, and at program start this block is copied to the ram section for "initialized variables".
If you program in other languages, then the behavior depends on the language and the startup behavior of the run-time.
If you consider an embedded micro with peripheral devices, for example UARTs or Capture blocks, these will always have a start-up definition provided by the chip maker. However my GOLDEN RULE is to never ever rely on this. If you want a peripheral to be initialized to a particular state, then initialize it. Every bit of every register, whether you think its is needed or not. This way YOU are always in control of the device state. [You know how sometimes a PC device turns to crap, eg USB won't work... and after a reboot it still won't work. But after a power cycle it does. Well guess what. Somebody made an assumption in the driver and did not initialise every bit of every register. Bad!]
Actually, I have a few golden rules for embedded device programming. There are more, but these are those about initialization, startup and running.
Hope this helps. Say so if you want a few more practices that make embedded devices robust.
So, not so much standardized... Expect there could be ANYTHING there if you didn't set it yourself.
I would not make any assumptions. It probably depends on the hardware and the OS.